贝加莱通用混合模块X20CM8281

贝加莱通用混合模块X20CM8281，奥地利贝加莱B&R全新原装进口，特价优势供应；主营品牌：博世力士乐（BOSCH-REXROTH）及安沃驰AVENTICS、迪普马DUPLOMATIC、爱尔泰克AIRTEC、本特利Bently、贝加莱B&R、世格ASCO、阿托斯ATOS、派克。威格士。
 
贝加莱B&R模块X20CM8281
物料号:
X20CM8281
描述:
数字和模拟通道
AI和AO的可选电流和电压
计数器功能
该模块为通用混合模块。在这个模块上，数字I/O和模拟I/O被组合在一起。根据需要，电流或电压信号可用于模拟I/O。两个数字输入上的计数器功能扩大了使用范围。
简短说明
I/O模块4个数字输入、2个数字输出、1个模拟输入、1个数字输出，具有特殊功能
一般信息
B&R ID代码0x24C3
每个通道的状态指示器I/O功能、操作状态、模块状态
诊断
模块运行/错误是，使用LED状态指示灯和软件
模拟输入是，使用LED状态指示器和软件
数字输出是，使用LED状态指示器和软件（输出错误状态）
电力消耗
0.01 W总线
内部I/O 1.75 W
致动器引起的额外功耗（电阻）[W]-
认证证书
CE是
UKCA是
ATEX 2区，II 3G Ex nA nC IIA T5 Gc
IP20，Ta（见X20用户手册）
09年ATEX 0083X
UL认证E115267
工业控制设备
HazLoc cCSAus 244665
过程控制设备
用于危险场所
I类，2区，ABCD组，T5
DNV温度：B（0至55°C）
湿度：B（高达100%）
振动：B（4 g）
EMC:B（桥梁和露天甲板）
CCS是
LR ENV1
KR是
ABS是
BV EC33B
温度：5-55°C
振动：4 g
EMC：桥梁和露天甲板
KC是
数字输入
数量4
标称电压24 VDC
输入特性符合EN 61131-2类型1
输入电压24 VDC-15%/+20%
24 VDC典型输入电流。3.3毫安
输入电路接收器
输入过滤器
硬件≤2µs
软件默认值为1ms，可在0到25ms之间配置，增量为0.2ms
连接类型1-wire连接
输入电阻类型。7.18 kΩ
附加功能20 kHz事件计数、门测量
切换阈值
低<5 VDC
高压>15VDC
通道和母线之间的绝缘电压500Veff
事件计数器
数量2
信号形式方波脉冲
评估每个负边，循环计数器
大输入频率。20千赫
计数器1输入1
计数器2输入3
计数器频率大值。20千赫
计数器大小16位
闸门时间测量
数量1
信号形式方波脉冲
评估正边缘-负边缘
计数器频率
内部48 MHz、24 MHz、12 MHz、6 MHz、3 MHz、1.5 MHz、750 kHz、375 kHz、187.5 kHz
计数器大小16位
脉冲之间的暂停时间≥100µs
脉冲长度≥20µs
支持的输入输入4
模拟输入
数量1
通过不同的端子连接输入±10 V或0至20 mA/4至20 mA
输入类型单端
数字转换器分辨率
电压±12位
当前12位
转换时间400µs，转换与X2X链路周期异步运行
输出格式INT
输出格式
电压INT 0x8001-0x7FFF/1 LSB=0x0008=2.441 mV
当前INT 0x0000-0x7FFF/1 LSB=0x0008=4.883µA
信号范围内的输入阻抗
电压>1 MΩ
当前-
负载
电压-
电流<300Ω
输入保护电源电压接线保护
允许的输入信号
大电压。±15v
大电流。±50毫安
过载时的数字值输出
拍摄不足
电压0x8001
当前0x0000
超过
电压0x7FFF
当前0x7FFF
转换过程逐次逼近
输入滤波器二阶低通滤波器/截止频率1 kHz
大误差
电压
收益0.08%
偏移0.02%
当前
增益0至20mA=0.08%/4至20mA=0.1%
偏移0至20毫安=0.03%/4至20毫安=0.16%
大增益漂移
电压0.01%/°C
电流0至20mA=0.009%/°C
4至20mA=0.0113%/°C
大偏移漂移
电压0.002%/°C
电流0至20mA=0.004%/°C
4至20mA=0.005%/°C
非线性
电压<0.02%
电流<0.02%
通道和母线之间的绝缘电压500Veff
数字输出
数量2
可变电流源FET
标称电压24 VDC
开关电压24 VDC-15%/+20%
标称输出电流0.5A
总标称电流1A
连接类型1-wire连接
输出电路源
输出保护过电流或短路时的热关断、开关电感负载的集成保护、反极性保护
诊断状态输出监测，延迟10ms
输出关闭时的漏电流为5µA
RDS（开启）105 mΩ
峰值短路电流<14A
过载停机或短路停机时打开电源。10ms（取决于模块温度）
切换延迟
0→1<250µs
1→0<270µs
开关频率
大电阻负载。100赫兹
电感负载见“切换电感负载”一节。
关闭感应负载时的制动电压。50伏直流电
通道和母线之间的绝缘电压500Veff
模拟输出
数量1
通过不同的端子连接输出±10 V或0至20 mA
数字转换器分辨率12位
转换时间300µs，转换与X2X链路周期异步运行
整个范围内输出变化的稳定时间为1ms
打开/关闭行为启动和错误内部启用继电器
大误差
电压
增益0.04%
偏移0.0225%
当前
增益0.05%
偏移0.125%
输出保护防短路
输出格式
电压INT 0x8001-0x7FFF/1 LSB=0x0010=4.882 mV
当前INT 0x0000-0x7FFF/1 LSB=0x0010=9.766µA
每个通道的负载
大电压。±10 mA，负载≥1 kΩ
大电流。负载为400Ω
大增益漂移
电压0.012%/°C
电流0.014%/°C
大偏移漂移
电压0.0075%/°C
电流0.03%/°C
负载变化引起的错误
大电压。0.02%，从10 MΩ→1 kΩ，电阻性
大电流。0.5%，从1Ω到400Ω，电阻
非线性<0.1%
通道和母线之间的绝缘电压500Veff
电气性能
电气隔离
通道与总线隔离
通道未与通道隔离
操作条件
安装方向
水平是
垂直是
安装海拔高度
0至2000米无限制
>2000米每100米环境温度降低0.5°C
防护等级符合EN 60529 IP20
环境条件
温度
操作
水平安装方向-25至60°C
垂直安装方向-25至50°C
降额见“降额”一节。
储存-40至85°C
运输-40至85°C
相对湿度
运行5%至95%，非冷凝
储存5%至95%，不凝结
运输5%至95%，不凝结
机械性能
注意：单独订购1x接线端子X20TB12。
单独订购1x总线模块X20BM11。
间距12.5+0.2mm

贝加莱数字量输入/输出
X20CM1201
X20CM8281
X20DM9324
X20RT8001
X20RT8201
X20RT8202
X20RT8401
贝加莱模拟量输入
X20AI1744
X20AI1744-3
X20AI2222
X20AI2237
X20AI2322
X20AI2437
X20AI2438
X20AI2622
X20AI2632
X20AI2632-1
X20AI2636
X20AI4222
X20AI4322
X20AI4622
X20AI4632
X20AI4632-1
X20AI4636
X20AI8221
X20AI8321
X20AIA744
X20AIB744
X20AP3111
X20AP3121
X20AP3122
X20AP3131
X20AP3132
X20AP3161
X20AP3171
X20CM0985
X20CM0985-1
X20CM8281
X20RT8201
X20RT8401
贝加莱模拟量输出
X20AO2437
X20AO2438
X20AO2622
X20AO2632
X20AO2632-1
X20AO4622
X20AO4632
X20AO4632-1
X20AO4635
X20CM8281
X20RT8202
X20RT8401
贝加莱温度测量
X20AT2222
X20AT2311
X20AT2402
X20AT4222.
X20AT4232
X20AT6402
X20ATA312
X20ATA492
X20ATB312
X20ATC402
贝加莱电机控制器
X20MM2436
X20MM3332
X20MM4331
X20MM4455
X20MM4456
X20SM1426
X20SM1436
贝加莱其它功能
X20CM0985
X20CM0985-1
X20CM4323
X20CM4810
X20CM6209
X20CM8281
X20CM8323
X20CMR010
X20DS4387
X20DS438A
X20PD0011
X20PD0012
X20PD0016
X20PD2113
X20PS4951
贝加莱计数功能
X20CM1201
X20CM1941
X20CM8281
X20DC1073
X20DC1176
X20DC1178
X20DC1196
X20DC1198
X20DC11A6
X20DC1376
X20DC137A
X20DC1396
X20DC1398
X20DC1976
X20DC2190
X20DC2395
X20DC2396

贝加莱B&R电机电缆
物料号:
8CM015.12-3
描述:
可用于电缆拖链
专门组装用于ACOPOS 1180/1320伺服驱动器和B&R伺服电机，电机连接器尺寸为1
电机电缆，长度15 m，4x 4 mm²+2x 0.75 mm²+2x 1 mm²，8针内螺纹Intercontec电机连接器尺寸1，可用于电缆拖链
一般信息
电缆横截面4 x 4 mm²+2 x 0.75 mm²+2 x 1 mm²
耐久性耐油性符合HD 22.10附录A和DIN EN 60811-404
证书E170315 cRUus AWM STYLE 21223 AWM I/II A/B 80°C 1000 V FT1
认证
CE是
UKCA是
UL cULus E225616
功率转换设备
EAC是
电缆施工
电力线
数量4
电线绝缘PP
电线颜色黑色、棕色、蓝色、黄色/绿色
变型镀锡铜绞线
横截面4 mm²
屏蔽号
搁浅否
信号线
数量4
电线绝缘PP
电线颜色白色、白色/红色、白色/蓝色、白色/绿色
变型镀锡铜绞线
横截面2 x 0.75 mm²+2 x 1 mm²
屏蔽成对单独屏蔽，镀锡铜编织，光学覆盖率>85%，箔屏蔽
Stranding White with White/red and White/blue with White/green
带填充元件和箔屏蔽的电缆绞合
电缆屏蔽镀锡铜编织，光学覆盖率>85%和箔屏蔽
外护套
材料TPU
橙色，类似于RAL 2003平面
标签B&R 4 G 4+（2x0.75）C+（2x1）C C E170315 cRUus AWM STYLE 21223 AWM I/II A/B 80°C 1000 V FT1
连接器
型号8针内螺纹speedtec电机连接器，尺寸1.0
交配周期<500
触点8（4个电源触点和4个信号触点）
连接时的防护等级符合EN 60529 IP66/67
电气特性
工作电压。1000真空（UL）
试验电压
电线-电线4 kV
屏蔽线4 kV
导体电阻
电力线≤5.1Ω/km
信号线0.75mm²：≤26.7Ω/km，1mm²：≤20Ω/km
绝缘电阻≥500 MΩ*公里
载流能力符合DIN VDE 0298第4部分表11
壁挂式30 A
安装在导管或电缆管道中30 A
安装在电缆桥架中30 A
环境条件
温度
移动-20°C至+80°C
静态-20°C至+90°C
机械性能
尺寸
长度15m
直径15.4 mm±0.4 mm
弯曲半径
单个弯曲>48 mm
移动>119毫米
拖动链数据
加速度。50 m/s²（取决于行进路径的长度）
弹性周期≥5000000
速度。300米/分钟
重量4.2 kg


贝加莱B&R旋变电缆
物料号:
8CR015.12-1
描述:
可用于电缆拖链
专门组装用于ACOPOS伺服驱动器和B&R伺服电机
分解器电缆，长度15 m，3x 2x 24 AWG（19x 0.127），12针内螺纹Intercontec分解器连接器，9针外螺纹DSUB伺服连接器，可用于电缆拖链
一般信息
电缆横截面3x 2x 24 19 AWG
耐久性符合VDE 0472第803部分的耐油性以及标准液压油
认证UL AWM 20671型，90°C，30 V，E63216和CSA AWM，90°C.30 V，I/II A/B FT1 LL46064
认证
CE是
UKCA是
UL cULus E225616
功率转换设备
电缆施工
信号线
数量6
电线绝缘特殊热塑性材料
电线颜色白色/棕色、绿色/黄色、灰色/粉色
变型镀锡铜绞线
横截面24 AWG/19 AWG
屏蔽号
搁浅白色与棕色，绿色与黄色，灰色与粉色
电缆绞合用箔屏蔽将3对电缆绞合在一起
电缆屏蔽铜编织，光学覆盖率≥90%，箔屏蔽
外护套
材料PUR
绿色，类似于RAL 6018平面
标签B&R 3x2x24 AWG FLEX UL AWM STYLE 20671 90°C 30 V E63216 CSA AWM 90°C 30V I/II A/B FT1 LL46064
连接器
类型12针内螺纹Intercontec解析器连接器
交配周期<500
12
附加连接器9针公DSUB伺服连接器
交配周期：<200
：9
连接时的防护等级符合EN 60529:IP20
连接时的防护等级符合EN 60529 IP66/67
电气特性
工作电压≤30 Veff
试验电压
电线-1.5 kV电线
电线-屏蔽0.8 kV
导体电阻
信号线≤86Ω/km
绝缘电阻>200 MΩ*km
环境条件
温度
移动-20°C至+80°C
静态-20°C至+90°C
机械性能
尺寸
长度15m
直径6.5 mm±0.2 mm
弯曲半径
单个弯头≥20 mm
移动≥50 mm
拖动链数据
加速度≤6 g
弹性周期>3000000
速度≤4 m/s
重量1.1 kg


贝加莱B&R电缆
物料号:
9A0017.02
描述:
零调制解调器电缆RS232，1.8米，用于连接UPS和IPC（9针内螺纹DSUB连接器-9针内孔DSUB连接器）
一般信息
认证
CE是
UKCA是
机械性能
尺寸
长度1.8米

贝加莱B&R电机电缆带制动
物料号:
80CM15002.21-01
描述:
电机电缆，长度15 m，5x 0.75 mm²，2x 0.5 mm²，用于带制动器的步进电机，电机侧有4针和2针连接器，可用于电缆拖链，UL列出
一般信息
电缆横截面5x 0.75 mm²+1x 2x 0.5 mm²
耐久性符合VDE 0472第803部分的耐油性以及标准液压油
认证UL AWM样式20234，80°C，1000 V，E63216和CSA AWM I/II A/B，90°C，1000V，FT2 LL46064
电缆施工
电力线
数量5
电线绝缘特殊热塑性材料
电线颜色黑色、棕色、蓝色、绿色、黄色/绿色
变型镀锡铜绞线
横截面0.75 mm²
屏蔽号
搁浅否
信号线
数量2
电线绝缘特殊热塑性材料
电线颜色白色、白色/红色
变型镀锡铜绞线
横截面0.5 mm²
屏蔽成对的单独屏蔽、镀锡铜编织、光学覆盖率>85%和箔带
白色与白色/红色交织
带填充元件和箔带的电缆绞合
电缆屏蔽镀锡铜编织，光学覆盖率>85%，包裹在隔离膜中
外护套
材料PUR
橙色，类似于RAL 2003平面
标签B&R 5x0.75+1x2x0.5 FLEX UL AWM STYLE 20234 80°C 1000 V E63216 CSA AWM I/II A/B 90°C 1000伏FT2 LL46064
电气特性
试验电压
电线-电线3 kV
屏蔽线3 kV
导体电阻
电力线≤29Ω/km
信号线≤39Ω/km
绝缘电阻>200 MΩ/km
载流能力符合DIN VDE 0298第4部分表11
壁挂式13 A
安装在导管或电缆管道中11.5 A
安装在电缆槽中13.5 A
环境条件
温度
移动-10至70°C
静态-20至90°C
机械性能
尺寸
长度15m
直径10.8 mm±0.4 mm
弯曲半径
单弯头>34 mm
移动≥85 mm
拖动链数据
加速度<60 m/s²
弹性周期≥3000000
速度≤4 m/s
重量0.26 kg/m

贝加莱B&R I/O供电电缆
物料号:
X67CA0P00.0002
描述:
电源连接电缆，4针，直，0.25米
简短描述
附件电源连接电缆，4针，直，0.25米
一般信息
注：不含聚氯乙烯和硅树脂
PWIS和无卤素
耐久性良好的耐化学性和耐油性
阻燃剂
良好的紫外线和臭氧耐受性
简短描述电源连接电缆，0.25米
类型连接电缆
电缆横截面
AWG 4x 20 AWG
mm²4x 0.5 mm²
电缆施工
电缆屏蔽未屏蔽
外护套
材料聚氨酯（PUR）
性能CFC、镉和无铅
细绞线0.34 mm²（22 AWG）
6级（42x 0.1毫米/42x38 AWG）
颜色黑色
电线
电线绝缘聚丙烯（PP）9Y
电线颜色棕色、黑色、蓝色、白色
性能CFC、镉和无铅
屏蔽号
类型无涂层铜ETP1
细绞线（42x 0.1 mm/42x 38 AWG），6级
绞合未绞合
电气特性
标称电流。40°C时每个EN/触点4 A
每个UL/触点3安
连接电压。60伏交流/直流
工作电压。60伏
符合IEC 61076-2的II类绝缘等级
导线电阻≤57Ω/km
绝缘电阻≥100 MΩ
操作条件
防护等级符合EN 60529
连接器/联轴器IP67，仅当拧入时
环境条件
温度
运输-40至90°C
固定安装-30至90°C
柔性安装-25至60°C
机械性能
尺寸
长度0.25米
直径5 mm±0.2 mm
弯曲半径≥10倍外径
拖动链数据
加速度。5 m/s²
弹性周期500万
速度。3.3米/秒

贝加莱B&R I/O供电电缆
物料号:
X67CA0P20.0150
描述:
电源连接电缆，4针，直，15米
简短描述
附件电源连接电缆，4针，直，15米
一般信息
注：不含聚氯乙烯和硅树脂
PWIS和无卤素
耐久性良好的耐化学性和耐油性
阻燃剂
良好的紫外线和臭氧耐受性
简短说明电源连接电缆，15.0米
类型连接电缆
电缆横截面
AWG 4x 20 AWG
mm²4x 0.5 mm²
电缆施工
电缆屏蔽未屏蔽
外护套
材料聚氨酯（PUR）
性能CFC、镉和无铅
细绞线0.34 mm²（22 AWG）
6级（42x 0.1毫米/42x38 AWG）
颜色黑色
电线
电线绝缘聚丙烯（PP）9Y
电线颜色棕色、黑色、蓝色、白色
性能CFC、镉和无铅
屏蔽号
类型无涂层铜ETP1
细绞线（42x 0.1 mm/42x 38 AWG），6级
绞合未绞合
电气特性
标称电流。40°C时每个EN/触点4 A
每个UL/触点3安
连接电压。60伏交流/直流
工作电压。60伏
符合IEC 61076-2的II类绝缘等级
导线电阻≤57Ω/km
绝缘电阻≥100 MΩ
操作条件
防护等级符合EN 60529
连接器/联轴器IP67，仅当拧入时
环境条件
温度
运输-40至90°C
固定安装-30至90°C
柔性安装-25至60°C
机械性能
尺寸
长度15m
直径5 mm±0.2 mm
弯曲半径≥10倍外径
拖动链数据
加速度。5 m/s²
弹性周期500万
速度。3.3米/秒

贝加莱B&R Link电缆
物料号:
X67CA0X01.0002
描述:
X2X链路连接电缆，0.25米
简短描述
附件X2X链路连接电缆，M12，4针，直，0.25米
一般信息
注意无卤素
耐久性阻燃
类型连接电缆
电缆横截面
数据线
AWG 2x 24 AWG
mm²2x 0.25 mm²
电源线
AWG 2x 22 AWG
mm²2x 0.34 mm²
电缆施工
信号线
屏蔽铝箔配对屏蔽
绞合双绞线
电缆绞合0.35 mm²（AWG 22），带填料
电缆屏蔽镀锡铜编织，覆盖率>85%
外护套
材料热塑性聚氨酯（TPU）
特性无卤素
颜色为紫色
电线
性能镀锡铜绞线
镀锡铜-ETB1型
数据线：细绞线（19x 0.13 mm）
供应线：细绞线（19x 0.15 mm）
电线颜色
数据线蓝色、白色
电源线红色、黑色
电线绝缘
数据线Cell聚乙烯（PE）
电源线聚丙烯（PP）
电气特性
额定电压250 V
标称电流。40°C时为4 A/触点
连接电压。125伏交流/直流
工作电压。250伏
符合IEC 61076-2的II类绝缘等级
导线电阻数据线：≤78Ω/km
供电线路：≤55Ω/km
绝缘电阻≥100 MΩ
操作条件
防护等级符合EN 60529
连接器/联轴器IP67，仅当拧入时
环境条件
温度
运输-40至80°C
固定安装-40至80°C
柔性安装-25至60°C
机械性能
尺寸
长度0.25米
直径6.9 mm±0.2 mm
弯曲半径
固定安装≥7.5x外径7.0 mm
柔性安装≥15x外径7.0 mm
弯曲半径≥15x外径
拖动链数据
加速度。4 m/s²
弯曲周期。200万
速度。3米/秒
重量0.063 kg/m

贝加莱B&R Link电缆
物料号:
X67CA0X21.0150
描述:
X2X链路连接电缆，15米
简短描述
附件X2X链路连接电缆，M12，4针，直，15米
一般信息
注意无卤素
耐久性阻燃剂
简短说明X2X链路连接电缆，15.0米
类型连接电缆
电缆横截面
数据线
AWG 2x 24 AWG
mm²2x 0.25 mm²
电源线
AWG 2x 22 AWG
mm²2x 0.34 mm²
电缆施工
信号线
屏蔽铝箔配对屏蔽
绞合双绞线
电缆绞合0.35 mm²（AWG 22），带填料
电缆屏蔽镀锡铜编织，覆盖率>85%
外护套
材料热塑性聚氨酯（TPU）
特性无卤素
颜色为紫色
电线
性能镀锡铜绞线
类型镀锡铜ETB1
数据线：细绞线（19x 0.13 mm）
供应线：细绞线（19x 0.15 mm）
电线颜色
数据线蓝色、白色
电源线红色、黑色
电线绝缘
数据线Cell聚乙烯（PE）
电源线聚丙烯（PP）
电气特性
额定电压250 V
标称电流。40°C时为4 A/触点
连接电压。125伏交流/直流
工作电压。250伏
符合IEC 61076-2的II类绝缘等级
导线电阻数据线：≤78Ω/km
供电线路：≤55Ω/km
绝缘电阻≥100 MΩ
操作条件
防护等级符合EN 60529
连接器/联轴器IP67，仅当拧入时
环境条件
温度
运输-40至80°C
固定安装-40至80°C
柔性安装-25至60°C
机械性能
尺寸
长度15m
直径6.9 mm±0.2 mm
弯曲半径
固定安装≥7.5x外径7.0 mm
柔性安装≥15x外径7.0 mm
弯曲半径≥15x外径
拖动链数据
加速度。4 m/s²
弯曲周期。200万
速度。3米/秒
重量0.063 kg/m


贝加莱B&R UPS电源模块
物料号:
9A0100.17
描述:
C型UPS电池箱（更换件），2x 12 V，4.5 Ah，用于电池单元9A0100.16
一般信息
电池
类型霍克独眼巨人12 V 4.5 Ah
使用寿命长达15年
可变单电池（VRLA）
存储期间的服务间隔每6个月收费1次
认证
CE是
UKCA是
UL cULus E115267
工业控制设备
电气特性
标称电压12 V
容量4.5 Ah
电池充电数据
充电电流类型。二点八八一
环境条件
温度
操作-40至80°C
储存-65至80°C
运输-65至80°C
相对湿度
运行5%至95%，无冷凝
储存5%至95%，非冷凝
输送5%至95%，无冷凝
机械性能
尺寸
宽度38毫米
长度205 mm
高度102 mm
重量约。3600克


贝加莱B&R端子排
物料号:
0TB103.91
描述:
电源使用一排3针接线板0TB03.9x。
概述
许可证    
CE    是
UL    cULus E115267
工业控制设备
HazLoc    cULus HazLoc E180196
工业控制设备
用于危险场所
I 类， 部门 2， 组 ABCD，T4
DNV GL    温度: B(0 - 55 °C)
湿度: B（ 100）
振动: A(0.7 g)
EMC: B(电桥和开口板)
接线端子
备注    通过螺旋法兰实现防震
依照 UL 的额定数据
电极数量    3 个（母头）
夹紧装置类型    作为弹簧端子的规格 
电缆类型    仅铜导线（不是铝导线！）
网栅尺寸    5.08 mm
接口横截面积    
AWG 导线    AWG 26 至 12
带塑料套环的芯线末端套管    0.20 至 1.50 mm²
单芯    0.20 至 2.50 mm²
细芯    0.20 至 2.50 mm²
带芯线末端套管    0.20 至 1.50 mm²
电气属性
额定电压    300 V
额定电流     10 A / 触点
容积电阻    ≤ 5 mΩ
使用条件
依照 EN 61131-2 的脏污程度    脏污程度 2

贝加莱B&R端子排
物料号:
0TB1111.8010
描述:
单排11引脚0TB1111螺纹卡箍用于连接各种B&R模块。
接线板
注意：通过螺纹法兰防止振动
标称值符合UL
引脚数量11
接线板类型螺旋线夹
电缆类型只有铜线（没有铝线！）
节距3.5 mm
连接横截面
AWG电线28至14 AWG
金属丝端套，塑料覆盖0.20至1.50 mm²
单线0.20至1.50 mm²
细绞线0.20至1.50 mm²
带线端套管0.20至1.50 mm²
电气特性
标称电压300 V
标称电流10 A/触点
接触电阻≤4.2 mΩ


贝加莱B&R CF卡
物料号:
5CFCRD.1024-02
5CFCRD.1024-03
5CFCRD.1024-04
5CFCRD.1024-06
描述:
CompactFlash 1 GB ATA/IDE SanDisk
CompactFlash 1 GB Western Digital（SLC）
CompactFlash 1 GB B&R (SLC)
容量1 GB
数据保留期10年
数据可靠性<每读取1014位1个不可恢复错误
终身监控是
MTBF>4000000小时（25°C时）
服务无
支持的操作模式PIO模式0-4，多字DMA模式0-2
连续阅读
典型的8 MB/s
连续写入
典型的6 MB/s
认证
CE是
UKCA是
UL cULus E115267
工业控制设备
DNV温度：A（0至45°C）
湿度：B（高达100%）
振动：A（0.7 g）
EMC:B（桥梁和露天甲板）
耐力
SLC闪存是
擦除/写入周期
典型>2000000
磨损平衡静态
纠错码（ECC）是
S.M.A.R.T.支持编号
支持
硬件MP100/200、PP100/200、PPS00/400、PP500、PPC300、PPC700、PPC725、PPC800、Provit 2000、Provit 5000、APC620、APC680、APC810、APC820
操作系统
Windows 7 32位No
Windows 7 64位否
Windows嵌入式标准7 32位否
Windows嵌入式标准7 64位否
Windows XP版否
嵌入式Windows XP是
Windows嵌入式标准2009是
Windows CE 6.0是
Windows CE 5.0是
软件
PVI Transfer≥V2.57（PVI Development Setup≥V2.5.3.3005的一部分）
B&R嵌入式操作系统安装程序≥V2.21
环境条件
温度
操作0至70°C
储存-50至100°C
运输-50至100°C
相对湿度
运行8至95%，无冷凝
储存8至95%，非冷凝
运输8%至95%，无冷凝
振动
操作值。16.3克（159米/秒²0-峰值）
存储量。30克（294米/秒²0-峰值）
运输量。30克（294米/秒²0-峰值）
震惊
操作值。1000 g（9810 m/s²0-峰值）
存储量。3000克（29430米/秒²0-峰值）
运输量。3000克（29430米/秒²0-峰值）
高程
操作值。24383米
机械性能
尺寸
宽度42.8±0.10 mm
长度36.4±0.15毫米
高度3.3±0.10 mm
重量11.4克

贝加莱通用混合模块X20CM8281
X20CM8281 X20通用混合模块,4个输出端,24VDC,漏式,1线连接技术,2路数字量输出,0.5 A,源式,1线连接技术, 1个模拟量输入,±10 V或0-20 mA/4-20 mA,12-bit分辨率,1个模拟量输出, ±10 V/0-20 mA,12-bit分辨率, 2个计数器可作为事件计数或门测量
 
贝加莱通用混合模块X20CM8281
模块（module）：完成特定功能的单元、部件或者子程序。
拨号连接由一个系列提供综合业务数字网（ISDN）主要速率接口（PRI）基本速率接口（BRI）的网络模块；集成数字调制解调器、模拟调制解调器、高密度的异步接口插槽以及异步/同步串行接口网络模块。
贝加莱通用混合模块X20CM8281

贝加莱8LS同步电机特点：
8LS三相同步电机
8LS系列三相同步电机是专为需要高动态特性和定位精度以及紧凑型结构应用而开发的的永磁电子换向同步电机。

NdFeB永磁体
正弦EnDat编码器或旋变器作为反馈单元
现在可用功能安全编码器
三相星型连接
尺寸紧凑，重量轻巧
良好的转子构造，使转动惯量***小化，保证了优异的动态特性
高负载能力/峰值扭矩
扭矩脉动低
高速时的高动态扭矩
寿命长，除轴承外所有电机部件免磨损
定子产生的功耗通过外壳直接转移到法兰上
预紧的深沟球轴承两端密封并油脂润滑
完整的电机产品线，堵转扭矩范围从0.2 Nm至115 Nm
采用两个SpeedTEC圆形插头进行电气连接
由ACOPOS伺服驱动器或ACOPOSmulti驱动系统控制

8LS三相同步电机不能直接与电源连接，它们只能与ACOPOS伺服驱动器或ACOPOSmulti驱动系统组合起来进行工作！

贝加莱8LS同步电机首选伺服电机类型：
8LSA25.D8060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D8060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.800 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D9060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D9060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 fit...
8LSA25.R0060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.800 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA35.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm;...
8LSA35.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DA060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DA060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.EA030D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; without holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA44.DA030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DA060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DA060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.EA030D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.DA030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA55.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.EA030D000-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D200-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D000-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D200-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA57.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA57.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA73.DA030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DA030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DB030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DB030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.R2030D000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
8LSA73.R2030D200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
8LSA75.DA030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DA030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DB030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 43.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 fit...
8LSA75.R2030D200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
贝加莱通用混合模块X20CM8281



标准型减速器独特的积木式组合设计
标准型减速器是一级减速比i= 3，4，5，8和10，背隙为≤ 8 - ≤ 15弧分。此外，它还提供二级和三级设计。在产品线的顶端，特级型减速器系列提供背隙≤1弧分，并具有高输出 扭矩。贝加莱标准型减速器系列可以为您提供市面上存在的所有同轴行星减速器的输出形状供您选择。
这使贝加莱在无需更改机器的情况下就能为现有的应用提供减速器。
就8GP55系列而言，在不需要极端小的背隙的应用中，可以将8GP60的输出轴承和输出形状与标准的扭矩结合。这样可以以经济高效的方式解决高轴向力和径向力。
标准系列中背隙足够的情况下，在需要更高轴承力的应用中，它提供了经济高效的解决方案。
贝加莱通用混合模块X20CM8281
贝加莱ACOPOS。
1.ACOPOS CPU模块
8AC140.60-2,插入模块, CPU, 兼容 x86 100 MHz Intel , 16MB DRAM, 32kB SRAM, 应用软件内存可更换: Compact-Flash, 1个CAN接口, 1个Profibus-DP从站接口, 1个RS232接口. 需单独订购应用软件内存!
8AC140.61-2,插入模块, CPU, ARNC0, 兼容 x 86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 应用软件内存可更换:
CompactFlash, 1个CAN 接口, 1个 Ethernet接口, 1个Profibus-DP从站 接口,, 1个RS232 接口. 需单独订购应用软件
内存!
8AC141.60-2,插入模块, CPU, 兼容x 86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 应用软件内存可更换: Compact-Flash, 2个CAN 接口,1个X 2X接口, 1个Ethernet接口, 1个RS232 接口, 需单独订购应用软件内存!
8AC141.61-2,插入模块, CPU, ARNC0, 兼容x86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 应用软件内存可更换:
CompactFlash, 2个CAN 接口, 1个X2 X 接口, 1个Ethernet接口, 1个RS232 接口, 需单独订购应用软件内存!
2.ACOPOS I/O模块
8AC130.60-1,插入模块, 8个数字量 I/O可成对配置为 24V 输入或 400/ 100mA输出, 2个数字量输出 2A, 需单独订购TB712端子排
8AC131.60-1,插入模块, 2个模拟量输入±10V, 2个数字量 I/O，可作为 24V输入或 45mA输出, 需单独订购TB712 端子排
3.ACOPOS编码器模块
8AC120.60-1,插入模块, EnDat编码器和正弦增量编码器接口
8AC122.60-2,插入模块, 旋变接口
8AC123.60-1,插入模块, 增量编码器和 SSI绝对值编码器接口
4.ACOPOS网络模块
8AC110.60-2,插入模块, CAN 总线接口
8AC112.60-1,插入模块, ETHERNET Powerlink 接口
5.ACOPOS 伺服驱动
8V1010.50-2,伺服驱动 3x 110- 230V / 1?x? 110- 230V?? 2.0A ?0.45?kW, 集成线路滤波器，制动电阻和安全重启抑制
8V1016.50-2,伺服驱动 3x 110- 230V / 1?x? 110- 230V?? 3.2A ?0.7?kW, 集成线路滤波器，制动电阻和安全重启抑制
8V1010.00-2,伺服驱动 3x 400- 480V ?1.0A ?0.45 kW, 集成线路滤波器，制动电阻和安全重启抑制
8V1016.00-2,伺服驱动 3x 400- 480V ?1.6A ?0.7 kW, 集成线路滤波器，制动电阻和安全重启抑制
8V1022.00-2,伺服驱动 3x 400- 480V ?2.2 A ?1kW,集成线路滤波器，制动电阻和安全重启抑制
8V1045.00-2,伺服驱动 3x 400- 480V ?4.4 A ?2kW,集成线路滤波器，制动电阻和安全重启抑制
8V1090.00-2,伺服驱动 3x 400- 480V ?8.8 A ?4kW,集成线路滤波器，制动电阻和安全重启抑制
8V1180.00-2,伺服驱动 3x 400- 480V ?19A ?9kW, 集成线路滤波器，制动电阻和安全重启抑制，DC总线电源
8V1320.00-2,伺服驱动 3x 400- 480V ?34A ?16kW, 集成线路滤波器，制动电阻和安全重启抑制，DC总线电源
8V1640.00-2,伺服驱动 3x 400- 480V ?64A ?32kW, 集成线路滤波器，制动电阻和安全重启抑制，DC总线电源
8V128M.00-2,伺服驱动 3x 400- 480V ?128A ?64kW, 集成线路滤波器，制动电阻和安全重启抑制，DC总线电源
贝加莱通用混合模块X20CM8281